Skip to content

About

Open Source Drone From Power to Analog Communications

Resources

Stars

1 star

Watchers

0 watching

Forks

Latest commit

 

History

3 Commits

Folders and files

NameName
Last commit message
Last commit date
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

OpenSourceDrone

Open-source drone electronics, from battery input through to the analogue video and control links. The repository holds the KiCad 8 design database for FCSTMV1.05 — a six-layer, impedance-controlled board that carries an STM32F405 quadrotor flight controller, a four-channel ESC, a 5.8 GHz analogue video link and a 2.4 GHz control link — together with the schematic PDFs for the ESC, video and control-link subsystems, and a complete fabrication output set.

Status, stated plainly

This is a design repository. Nothing here has been fabricated, assembled or powered.

There is no aircraft. No board has been ordered from a fab, no part has been reflowed, no rail has been brought up and nothing has flown. The repository contains schematics, a PCB layout, Gerbers and a BOM — design artefacts only. There are no measurements of any kind: no scope captures, no efficiency curves, no thermal data, no range tests.

The layout also carries unresolved review notes from the designer, reproduced verbatim in Outstanding design work below. Treat the current Gerbers as a snapshot of work in progress, not a released fab package.


Repository layout

Path Contents
FCSTMV1.05.kicad_pro / .kicad_pcb / .kicad_sch KiCad project, PCB layout and root schematic sheet
Part2.kicad_sch … Part7.kicad_sch Per-subsystem schematic sheets (see note below)
FCSTMV1.05-backups/ KiCad auto-backups, V1.03 through V1.05
Gerbers/ Current Gerber set, drill files and job file
Gerbers-10.17.zip, -10.18.zip, -10.19.zip Dated Gerber snapshots; 10.19 is current
Assembly/ Pick-and-place position files, top and bottom
bom/ibom.html Interactive BOM
FCSTMV1.05-10.17/18/19.csv BOM snapshots; 10.19 is current
Required_impedance_control-10.18.xlsx Controlled-impedance table for the fab
FC.pdf Flight controller schematic
ESCPart1.pdf, ESCPart2.pdf ESC schematic
VTX.pdf, VRX.pdf 5.8 GHz video transmitter and receiver
CTX.pdf, CRX.pdf 2.4 GHz control-link transmitter and receiver
fp-info-cache KiCad footprint cache

Board overview

FCSTMV1.05 is a single six-layer profile measuring 497.46 × 154.73 mm, on which every subsystem is laid out side by side and labelled on the top silkscreen: FC, four ESC channels, VTX, CRX, POWER, GPS, MAG, IMU, BARO, OSD, BLE, FLASH, USB, SBUS, LEDS and BUZZER.

Everything about the physical form points at a bench bring-up vehicle rather than a flyable board. Of 1,182 placements across 206 BOM lines, the single largest group is 171 individual 2.54 mm pin sockets, followed by 44 three-way headers, 42 two-way headers and 47 SMD wire pads — nearly every net is broken out. Passives are 1206 with hand-solder pads. One silkscreen note reads Not Connected at all - choose your own pins. A flight article would be a fraction of this size on a stack-mount footprint.

Metric Value
Layers 6 (F.Cu, In1.Cu … In4.Cu, B.Cu)
Profile 497.46 × 154.73 mm
Finished thickness 1.653 mm modelled; fab note specifies 1.6 mm
Placed footprints 1,198
Vias 1,544
PTH drill hits 2,396 across ten tools, 0.30 mm – 4.55 mm
NPTH drill hits 12, 1.02 mm and 2.80 mm
Surface finish Not specified in the job file (Finish: None)

Stackup

Taken from the stackup stored in FCSTMV1.05.kicad_pcb and echoed in the Gerber job file. All dielectrics are FR4; the prepreg and core layers are thickness-locked.

Layer Type Thickness (mm) εr tan δ
F.Mask Solder mask 0.05
F.Cu (L1) Copper 0.0175
dielectric 1 Prepreg 0.1785 4.74 0.02
In1.Cu (L2) Copper 0.035
dielectric 2 Core 0.43 4.60 0.02
In2.Cu (L3) Copper 0.035
dielectric 3 Prepreg 0.161 4.74 0.02
In3.Cu (L4) Copper 0.035
dielectric 4 Core 0.43 4.60 0.02
In4.Cu (L5) Copper 0.035
dielectric 5 Prepreg 0.1785 4.74 0.02
B.Cu (L6) Copper 0.0175
B.Mask Solder mask 0.05

KiCad models the outer copper at its 0.0175 mm base weight. The fabrication note on the Cmts.User layer states the intended finished specification:

Thickness: 1.6MM Finished Outer Copper: 1OZ Inner Copper: 1OZ Inner layer Residual copper ratio: 50%

In1.Cu and In4.Cu are the impedance reference planes for the outer layers.

Controlled impedance

Required_impedance_control-10.18.xlsx specifies fifteen controlled traces at ±10%. Every entry uses a 0.2 mm clearance to the adjacent copper pour.

Impedance Type Signal / reference layer Trace width Count
90 Ω differential Differential pair, non-coplanar L1/L2 and L6/L5 0.16 mm 2
50 Ω CPWG L1/L2 and L6/L5 0.10 mm 5
75 Ω CPWG L1/L2, L6/L5, L4/L5 0.16 mm 8

The 90 Ω pairs are the USB differential signalling, the 50 Ω lines are the 2.4 GHz and 5.8 GHz RF paths, and the 75 Ω lines are analogue composite video. A drawing-layer note asks Check if antenna only 50 OHM and rest video stuff is 75 OHM, so the split is not finally settled.

Subsystems and key components

A note on the schematic files. The design is not hierarchical. FCSTMV1.05.kicad_sch is a single flat sheet on a 2000 × 2000 mm page that carries the entire design and is the one the PCB is annotated against. Part2.kicad_sch through Part7.kicad_sch are standalone A0 sheets that mirror one subsystem each and correspond to the PDFs; none of them is referenced by the root, so KiCad will not open them as child sheets and their reference designators are numbered independently. Editing a PartN sheet does not change the board.

Reference designators below are those on the root sheet; the sheet named in each heading is the standalone file covering that subsystem.

Flight controller — Part3.kicad_sch

Part Manufacturer Ref Function
STM32F405ZGTx STMicroelectronics U5 Cortex-M4F flight controller MCU, LQFP144
ICM-42688-P TDK InvenSense U7 Six-axis gyro and accelerometer
BMP390 Bosch IC9 Barometric pressure sensor
MMC5983MA MEMSIC IC10 Three-axis magnetometer
SAM-M10Q-00B u-blox ANT2 GNSS module, integrated antenna
AT7456E — U8 Analogue OSD character generator
W25Q128JVSIQ Winbond U15 128 Mbit SPI NOR flash
NINA-B416-01B u-blox U9 Bluetooth LE module
TXS0104EPWR Texas Instruments IC7 Four-bit bidirectional level shifter
USB4730-GF-A-KIT GCT J138 USB-C receptacle
TPD4EUSB30DQAR Texas Instruments IC1 USB ESD protection
TPS7A2033PDBVR Texas Instruments IC8 3.3 V LDO
CMT-8504-100-SMT-TR Same Sky LS1 Magnetic buzzer
PTS647SK70SMTR2N C&K S1–S5 Tactile switches

ESC, four channels — Part5.kicad_sch and Part7.kicad_sch

Each sheet carries two complete channels; four channels in total.

Part Manufacturer Qty Function
STM32F051C8Tx STMicroelectronics 4 Per-channel ESC MCU
DRV8300DRGER Texas Instruments 4 Three-phase gate driver
PSMN1R4-40YLDX Nexperia 24 40 V, 1.4 mΩ N-channel MOSFET, six per channel
INA240A1D Texas Instruments 4 Bidirectional current-sense amplifier
PMEG4010CEJ Nexperia 12 Schottky diode

Power — Part4.kicad_sch

Part Manufacturer Qty Function
XT60-M AMASS 1 Main battery input
XT30PW-M AMASS 1 Secondary power connector
LT8612IUDE#PBF Analog Devices 2 42 V, 6 A synchronous buck
LMR33630ADDA Texas Instruments 4 36 V, 3 A synchronous buck
TPS61169DCKR Texas Instruments 1 38 V boost LED driver
ADPL40502AUJZ-1.2-R7 Analog Devices 1 200 mA low-noise LDO
SMCJ33A Littelfuse 2 33 V, 1500 W TVS
SMF5V0A-E3-08 Vishay 1 5 V TVS

2.4 GHz control link — Part4.kicad_sch

Part Manufacturer Qty Function
SX1280IMLTRT Semtech 2 2.4 GHz LoRa / FLRC transceiver
ESP32-C3-MINI-1-H4X Espressif 1 RISC-V link co-processor
ESP32-WROOM-32E-H4 Espressif 1 Link co-processor
2450FM07D0034001T Johanson 2 2.45 GHz filter matched to the SX1280
47948-0001 Molex 2 2400–2483.5 MHz SMT chip antenna
0805USBN-121MRC Coilcraft 1 Common-mode choke (part number disputed, see below)
RKJXK1210002 ALPS Alpine 2 Multi-directional stick switch

Schematics for both ends of the link are in CTX.pdf and CRX.pdf.

5.8 GHz video link — Part2.kicad_sch (TX) and Part6.kicad_sch (RX)

Part Manufacturer Qty Function
RTC6705 — 1 5.8 GHz video transmitter
QPA9501TR13 Qorvo 1 5.1–5.9 GHz three-stage power amplifier
STM32G431KBU6 STMicroelectronics 1 VTX control MCU
RTC6715 — 1 5.8 GHz video receiver
SKY65404-31 Skyworks 1 4.9–5.9 GHz LNA, 16 dB gain, 1.5 dB NF
BFCN-5750+ Mini-Circuits 1 5.75 GHz band-pass filter
BFP520H6327XTSA1 Infineon 5 RF NPN transistor, SOT-343
ATMEGA4809-AF Microchip 2 Receiver control MCU
U.FL-R-SMT-1(10) Hirose 2 U.FL antenna connectors
54132-4062 Molex 1 40-way 0.5 mm FFC/FPC connector

Fabrication outputs

Current revision is 10.19. The Gerbers/ directory holds the loose files; the dated .zip archives are point-in-time snapshots of the same output.

Copper and technical layers — F_Cu, In1_Cu, In2_Cu, In3_Cu, In4_Cu, B_Cu, F_Mask, B_Mask, F_Paste, B_Paste, F_Silkscreen, B_Silkscreen, Edge_Cuts, plus FCSTMV1.05-job.gbrjob.

Drills — Gerbers/Drills/ holds FCSTMV1.05-PTH.drl and -NPTH.drl with their Excellon drill maps.

Assembly — Assembly/ holds FCSTMV1.05-top.pos, -bottom.pos and -all-pos.csv. -all-posORIG.csv is the unmodified KiCad export retained alongside the edited file.

BOM — FCSTMV1.05-10.19.csv is the current bill of materials, 206 lines and 1,182 placements. bom/ibom.html is a self-contained interactive BOM for assembly.

Before ordering, note that the 10.18 BOM snapshot exports with a zero quantity column and should not be used; 10.17 and 10.19 are intact.

Outstanding design work

The Dwgs.User and Cmts.User layers carry the designer's own open items. These are reproduced verbatim because they are the most accurate statement of what is left to do:

  • TODO:
  • Check Pins
  • Check Pad2Pad Clearance
  • NEED USB BOARD CLEARANCE
  • Make sure Power Tracks are wide enough
  • Thicken Power rails
  • Check Power Planes and Conn Traces
  • Put Vias on Pads and make smaller
  • Flip components and make smaller power pads
  • Can flip 5V or other component
  • Think of which way round connectors go
  • AVDD AND AVCC Planes from some mid ground or power planes
  • Check if antenna only 50 OHM and rest video stuff is 75 OHM
  • When does it stop behaving like CPWG and become a simple microstrip?
  • Check all how can cut tracks if problem?
  • NEED x4 ESC FOR REAL DESIGN
  • CHANGE NET NAMES FOR OTHER ESCs
  • UPDATE SILK SCREEN AT END AS UPDATE FROM PCB UNDOES IT / Make sure each silk is unique
  • ADD CURR BUS
  • Make a Copy & Update for PCBWay

Further items found while surveying the database, not annotated on the board. Each needs resolving before the design is ordered:

  • Two symbols disagree with themselves about which part they are. FL1 has Value 0805USBN-271MRC but Manufacturer_Part_Number 0805USBN-121MRC; these are different Coilcraft chokes and the footprint follows the -121. U9 has Value NINA-B416-01B but Manufacturer_Part_Number NINA-B416-00B, which are different u-blox module variants. Whichever field the BOM export happens to read determines what gets ordered.
  • Some Description fields are inherited from unrelated parts. FW520WFMT1 is described as an unpolarized capacitor, and BFCN-5750+ carries the description of the BFP520 transistor. Do not treat the description fields as authoritative.
  • The Gerber job file declares no surface finish (Finish: None). One must be specified when ordering.

Connector pinouts follow a note on the drawing layer: USE BETAFLIGHT CONNECTOR STANDARD. The receiver input is marked SBUS/F.PORT/SMARTBUS.

Firmware

No firmware lives in this repository. The flight firmware is being written separately in emb-drone-flight-stack — a C++20 flight stack targeting the STM32F405 on this board, covering the IMU driver, attitude estimation, the PID control loop, DShot output and the CRSF control link.

That repository also mirrors this hardware design under hardware/, and its STATUS.md is the authoritative record of firmware progress. As of the last update it builds and passes its host-side test suite; like the hardware here, it has never run on silicon.

Tooling

KiCad 8 — the schematic files carry format version 20231120 and the board 20240108, both written by generator version 8.0. Open FCSTMV1.05.kicad_pro to load the project; the schematic opens on the flat root sheet. The PartN sheets must be opened as separate files. fp-info-cache is committed so the footprint library resolves without a rescan.

Licence

No licence is currently declared for this repository. Until one is added, default copyright applies and reuse rights are not granted.

About

Open Source Drone From Power to Analog Communications

Resources

Stars

1 star

Watchers

0 watching

Forks

Releases

Packages

Contributors

Languages